# lever

## advantage of third class levers

You may be wondering why you would use a third-class lever when it doesnt change the direction or strength of the applied force. The advantage of a third-class lever is that the output force is applied over a greater distance than the input force. The output end of the lever must move faster than the input end in order to cover the greater distance. Q: A broom is a third-class lever when it is used to sweep a floor (see the Figure 1.1), so the output end of the lever moves faster than the input end. Why is this useful? A: By moving more quickly over the floor, the broom does the work faster.

## comparing classes of levers

All three classes of levers make work easier, but they do so in different ways. When the input and output forces are on opposite sides of the fulcrum, the lever changes the direction of the applied force. This occurs only with first-class levers. When both the input and output forces are on the same side of the fulcrum, the direction of the applied force does not change. This occurs with both second-class and third-class levers. When the input force is applied farther from the fulcrum than the output force is, the output force is greater than the input force, and the ideal mechanical advantage is greater than 1. This always occurs with second-class levers and may occur with first-class levers. When the input force is applied closer to the fulcrum than the output force is, the output force is less than the input force, and the ideal mechanical advantage is less than 1. This always occurs with third-class levers and may occur with first-class levers. When the input and output forces are the same distance from the fulcrum, the output force equals the input force, and the ideal mechanical advantage is 1. This occurs only with first some first-class levers.

## classes of levers

Other levers change force or distance in different ways than a hammer removing a nail. How a lever changes force or distance depends on the location of the input and output forces relative to the fulcrum. The input force is the force applied by the user to the lever. The output force is the force applied by the lever to the object. Based on the location of input and output forces, there are three basic types of levers, called first-class, second-class, and third-class levers. The Table 1.1 describes the three classes. Class of Lever Example of Lever in This Class First class Location of Input & Output Forces & Fulcrum* Ideal Mechanical Advantage Change in Direction of Force? Seesaw 1 <1 >1 yes yes yes Second class Wheelbarrow >1 no Third class Hockey stick <1 no = fulcrum I = input force O = output force The Table 1.1 includes the ideal mechanical advantage of each class of lever. The mechanical advantage is the factor by which a machine changes the input force. The ideal mechanical advantage is the increase or decrease in force that would occur if there were no friction to overcome in the use of the machine. Because all machines must overcome some friction, the ideal mechanical advantage is always somewhat greater than the actual mechanical advantage of the machine as it is used in the real world. Q: Which class of lever is a hammer when it is used to pry a nail out of a board? What is its mechanical advantage? A: To pry a nail out of a board, the fulcrum is located between the input and output forces. Therefore, when a hammer is used in this way it is a first class lever. The fulcrum is closer to the output force than the input force, so the mechanical advantage is >1. In other words, the hammer increases the force applied to it, making it easier to pry the nail out of the board.

## what is a lever

A lever is a simple machine consisting of a bar that rotates around a fixed point. The fixed point of a lever is called the fulcrum. Like other machines, a lever makes work easier by changing the force applied to the machine or the distance over which the force is applied. How does a hammer make it easier to pull a nail out of a board? First, it changes the direction of the force applied to the hammerthe hand pushes down on the handle while the claw end of the hammer head pulls up. Often, you can push down with more force than you can push up because you can put your own weight behind it. The hammer also increases the strength of the force that is applied to it. It easily pulls the nail out of the board, which you couldnt do with your hands alone. On the other hand, the hammer decreases the distance over which the force is applied. The hand pushing down on the handle moves the handle over a distance of several inches, whereas the hammer pulls up on the nail only an inch or two. Q: Where is the fulcrum of the hammer when it is used to pull a nail out of a board? In other words, around what point does the hammer rotate? A: The fulcrum is the point where the head of the hammer rests on the surface of the board.

## instructional diagrams

No diagram descriptions associated with this lesson

## questions

levers that change the direction of the force are

``````-->  a) first class levers.

b) second class levers.

c) third class levers.

d) all of the above
``````

examples of first-class levers include

``````-->  a) see saws.

b) wheelbarrows.

c) rakes.

d) two of the above
``````

all of the following are third-class levers except

``````a) brooms.

b) hockey sticks.

c) rakes.

-->  d) wheelbarrows.
``````

a second class lever always has an ideal mechanical advantage less than 1.

``````a. true

-->  b. false
``````

a third class lever always applies the output force over a greater distance than the input force.

``````-->  a. true

b. false
``````

## diagram questions

No diagram questions associated with this lesson